Your cart is currently empty!
Ford Ranger Intercooler PK 3LT
From A$1,545.00
Transmission oil black, working your Transmission to the max with that 28ft caravan on the back?
HPD has you covered when it comes to keeping your transmission working reliably within safe operation temperatures.
These days most vehicle manufactures either run the transmission oil through a heat exchanger that is cooled by coolant used by the engine or run through the bottom tank of your radiator. This can have an impact on the engines cooling system and transmission temps when everything is working hard. The other issue being when either of these systems fail it can be quite detrimental and expensive when you have the two fluids mix together.
HPD’s oil to air transmission coolers have been designed and tested to provide stable transmission temperatures under the toughest conditions. Our bar and plate construction ensure that these cores will hold up in extreme environments under intense towing loads and still provide cool and stable transmission oil temperatures.
All HPD transmission cooler kits come with everything required to install on to your vehicle. Kit consist of transmission cooler, stainless steel laser cut bracketry, billet CNC adaptor plate, hose tail fittings, support clamps, insulation, oil hose, nuts, bolts, washers and installation instructions.
Key Benefits:
- Reduced / stable temperatures
- Prolong transmission oil life
- Lower engine coolant temperatures
- Reduced stress / strain on transmission
- Better fuel economy
- Extends transmission life
This kit is a complete and comprehensive kit including everything needed to do the install.
We suggest that these kits be installed by a qualified mechanic to ensure safe and reliable operation.
**This kit is compatible with the Tickford Enhanced 3.2L Ranger which uses a thicker intercooler core**
**This kit may not be suitable for Ford Everest 3.2L, due to different front intrusion bar design**
Kit features:
- Bar & Plate Core 400x110x50mm
- CNC Machined Oil apaptor block
- Lasercut stainless steel mounting brackets
- CNC Machined end tanks
- 10mmø hoses included
Description
This HPD intercooler kit has been designed and created to suit Ford Ranger PJ / PK early models (2006-2011). The intercooler delivers reduced inlet temperature’s and engine running temperatures. The kit allows fitment of a winch and bull bar and re-positions the intercooler into a higher position that is less likely to suffer damage when off-roading. We also have a transmission cooler upgrade available for automatic transmissions.
NOTE: If your vehicle is Automatic we suggest you order the automatic transmission variant of this kit below as you will have to fabricate new mounting brackets for your existing transmission cooler as the new HPD intercooler will move to a higher location and will interfere with the factory mounting location of the factory transmission cooler.
This Ford Ranger 3.0L intercooler kit responds well with engine tuning. With the cooler intake temperatures produced from HPD’s intercooler kit enables a safe increase in torque and power.
Kit features:
- Bar & Plate Core 450x300x76mm
- Alloy mandrel bent piping
- Quality silicone hoses and clamps
- Laser cut Mounting brackets
- Winch & bull bar Compatible*
- Hot side piping 51mmø
- Cold side piping 57mmø
- Transmission cooler upgrade available for automatic transmission
- Transmission cooler 400x110x50mm
- Bolt on installation, no cutting holes for intercooler piping.
(NOTE: small modification will need to be made to factory bonnet latch support bracket)
HPD 4WD intercooler kits are designed to give amazing performance, reliability, consistent and sustainable power. By reducing inlet temperatures you will also reduce engine running temperatures.
The comprehensive kit has been manufactured with careful research and development. Each kit is vehicle specific with a heat exchanger, alloy mandrel bent piping, quality silicone hoses and fittings.
Our Intercooler Kits are easy to install with basic workshop tools and backed by the HPD team who can help you at any step of the way. With our dealer network Australia wide, you guys that don’t like to get your hands dirty can have your kit installed by a qualified technician. Our front mounted intercoolers don’t suffer from heat soak from high under bonnet temperatures like top mounted intercoolers or water to air intercoolers which at low speed – hard slogging can increase inlet temperatures.
HPD intercooler kits suit all the leading aftermarket turbo kits that don’t have an option for intercooling, allowing you to increase the performance, reliability and fuel efficiency of your 4WD.
*compatible with most aftermarket brands
| SKU | IK-FR-F |
|---|---|
| Mount | Front Mount Intercooler |
| Make | Ford |
| Model | Ranger PK 3.0L |
Additional information
| Weight | 10 kg |
|---|---|
| Part Number | IK-FR-F |
| Transmission | Manual – No Tranmission cooler kit required, Automatic – Please include transmission cooler + $600.00, Automatic – No transmission cooler thanks |
